Porosity in Castings: 7 Root Causes and How Foundries Fix Them
Publication Date : 2026-10-18 03:10:43

A buyer-focused guide to porosity in castings: how gas porosity differs from shrinkage porosity, the seven root causes behind most rejections, practical detection methods, and how to set acceptance criteria that hold up at incoming inspection.
Gas vs Shrinkage Porosity: Why the Distinction Determines the Fix
Porosity is the most common internal defect in castings, but treating it as one problem leads to the wrong countermeasures. Gas porosity forms when dissolved gas or entrapped air cannot escape before the metal freezes; the pores are typically round, smooth-walled, and often found near the surface or in the last regions to solidify. Shrinkage porosity forms when a feeding path closes before the thick section is fully fed; pores are irregular, jagged, and concentrated in hot spots such as thick bosses, junctions, and riser-adjacent zones. The practical difference matters: degassing and venting fix gas, while gating and riser design fix shrinkage, and a foundry that misdiagnoses the type will keep shipping the same defect.
As a rule of thumb, gas pores look spherical under a low-power microscope or on a fracture surface, and shrinkage pores look like interconnected sponges. Hydrogen is the main gas culprit in aluminium, with solubility dropping sharply at the freezing point; in steels, nitrogen and reoxidation products behave similarly. Shrinkage is driven by volume contraction during solidification, which is roughly 6-7% for many aluminium alloys and higher for some steels, so the feeder must supply that volume while the hot spot is still liquid. Ask your foundry which mechanism they identified before they propose a corrective action.
The Seven Root Causes and the Standard Fixes
Most porosity problems trace back to a small set of process variables. The checklist below is the one we use when a buyer sends us a porosity complaint with photos and a rejection rate.
1. Melt gas content: hydrogen pickup from damp charge materials, humid air, or contaminated flux. Fix: rotary degassing with argon or nitrogen, clean dry scrap, and a gas test (reduced-pressure test or a quantitative hydrogen analyser) before pouring. 2. Turbulent filling and entrained air: a badly designed runner or a pour that drops metal into the cavity pulls in air and oxide films. Fix: bottom gating, tapered runners, and a fill time that keeps gate velocity in a controlled range rather than a fast splash. 3. Inadequate feeding: undersized risers or a feeding path that necks off. Fix: riser sizing by modulus, chills in heavy sections, and simulation to confirm the hot spot is fed last. 4. Sand and mould issues: high moisture, poor permeability, or excessive binder causing gas generation at the interface. Fix: control sand moisture and permeability, use low-gas binders, and vent the mould and cores. 5. Die and tooling problems in die casting: poor venting, vacuum failure, or a shot profile that traps air. Fix: vent-area checks, vacuum validation, and shot-curve tuning. 6. Alloy and pouring temperature: overheating increases gas pickup and shrinkage; too cold causes misruns and cold shuts that mimic porosity. Fix: hold temperature in a defined window and log it per heat. 7. Section design: abrupt thickness changes create isolated hot spots that cannot be fed. Fix: gradual transitions, generous fillets, and design review before tooling.
A good foundry will not guess. Ask for the corrective action report with the defect type, the process variable changed, and the verification batch result. If the answer is only "we will improve the process," that is not a fix.
- Reduced-pressure gas test or hydrogen analyser result per melt
- Sand moisture and permeability records for green sand lines
- Pouring temperature log per heat, with the alloy window
- Shot curve and vacuum level records for die casting
- X-ray or sectioning of the first-off parts after any change
Detection Methods and What They Actually Reveal
Detection should match the defect and the acceptance criteria. Visual inspection and dye penetrant find surface-connected porosity only; they miss internal gas and shrinkage entirely. Radiography (X-ray) is the workhorse for internal porosity and shows size, distribution, and location, but it is insensitive to tight planar defects and depends on film or detector resolution. Ultrasonic testing is good for thicker sections and for planar defects, but it struggles with complex geometry and thin walls. Sectioning and metallography give the definitive answer on pore morphology, which is how you confirm gas versus shrinkage.
For production control, weigh the cost. X-ray of a sample per shift plus full inspection of safety-critical parts is a common compromise. Pressure tightness testing (air decay or water) is the right test for pump and valve bodies, because it measures the function the buyer actually needs. Whatever method you choose, define the sampling plan, the section being examined, and the acceptance threshold in the purchase order, not after the first rejection.
Acceptance Criteria: How to Write a Standard Buyers and Foundries Both Accept
Porosity acceptance is a specification decision, not a negotiation at the loading dock. The cleanest approach is to reference a recognised standard for the alloy and process, such as ASTM E505 for aluminium castings or ASTM E446/E186 for steel, and then add part-specific requirements. For critical machined surfaces, state the maximum pore size and the minimum distance from a sealing face; for non-critical areas, allow a higher level. If your drawing has no porosity callout, the foundry will default to its own internal level, which may not match your customer's expectation.
Set the criteria by function. A hydraulic housing needs pressure tightness at the specified test pressure, so define that test and the retest rule. A cosmetic cover needs a surface finish limit. A structural bracket needs a radiography level in the highest-stress zone. Put the sampling frequency, the test method, and the disposition of nonconforming parts in writing, and agree on who pays for the inspection. When you source through a platform, attach the porosity callout to the RFQ so every quoted foundry prices the same requirement.
- Reference standard and acceptance level per alloy and process
- Zones on the drawing with different limits (critical, machined, cosmetic)
- Test method, sampling frequency, and retest rule
- Disposition: rework, scrap, or concession, and who bears the cost
Frequently Asked Questions
Can porosity be repaired, or does it always mean scrap?
Surface porosity can sometimes be repaired by welding or impregnation, but internal shrinkage in a pressure-tight or structural part usually means scrap. Impregnation seals leaks but does not restore strength, so it is acceptable only if your specification allows it. Decide this before production, not after a rejection.
How do I tell gas porosity from shrinkage porosity on a broken part?
Look at the pore shape. Gas pores are round and smooth-walled; shrinkage pores are irregular, elongated, and often connected like a sponge. Location also helps: gas tends to sit near surfaces or in the last-to-freeze areas, while shrinkage sits in hot spots such as thick bosses and junctions.
What porosity level should I specify in the purchase order?
Specify a recognised standard level for the alloy and process, then add tighter limits for critical zones such as sealing faces and machined surfaces. Include the test method, sampling frequency, and disposition rules. If you leave the drawing silent, you are accepting the foundry's default.
Looking for a reliable casting supplier? Request a quote from Intercontinental Casting — our engineering team replies within one business day.