Surface Finish by Casting Process: Ra Numbers That Actually Matter
Publication Date : 2026-10-27 03:10:48

A practical guide to achievable Ra surface roughness by casting process (sand, investment, die, permanent mold), how finish affects sealing and painting, and how to specify Ra correctly on a purchase order so you get parts that fit, seal, and coat the first time.
Why Ra Is the Number Buyers Should Quote
Surface roughness is usually written as Ra, the arithmetic average deviation of the profile from its mean line, in micrometers. It is the single finish number most Chinese foundries can measure and most overseas buyers can verify with a portable profilometer. But Ra is an average, so a surface can hit 3.2 µm Ra while still carrying deep pores that leak air or telegraph through paint. Treat Ra as the entry ticket, not the whole specification.
The practical reason Ra matters is cost. Every step down in roughness adds process time: finer sand, more slurry coats, slower feed, extra polishing. Asking for 1.6 µm Ra on a sand casting that only needs to be painted is money burned on every part. The ranges below reflect what shops routinely hold in production, not one-off lab results.
Ra Ranges by Casting Process
Sand casting in green sand or resin-bonded sand typically lands at 12.5–25 µm Ra as-cast; with a good facing sand and controlled pouring you can hold 6.3–12.5 µm. Investment casting (lost wax) is much smoother: 3.2–6.3 µm Ra as-cast is normal, and 1.6 µm is achievable on critical faces with fine slurry and careful shell building. Die casting holds roughly 1.6–3.2 µm Ra on the die side, while permanent mold sits around 3.2–6.3 µm.
Two caveats matter more than the table. First, Ra varies across a single part: the drag side of a sand mold is rougher than the cope, and gate areas are rougher than the far end of the cavity. Second, any post-processing resets the number. Shot blasting, vibratory finishing, and tumbling change Ra by 1–3 µm in either direction depending on media. Specify the finish after the last operation the part sees, not as-cast if the part will be blasted.
How Finish Drives Sealing and Painting
For sealing, the controlling feature is not average roughness but the presence of connected porosity and the depth of surface pits. A sand casting at 12.5 µm Ra with open surface pores will weep through a gasket face even if the Ra looks acceptable on paper. For hydraulic and pneumatic parts, specify a machined sealing face at 1.6 µm Ra or better, or require impregnation before pressure testing. Investment castings at 3.2 µm Ra often seal directly with a proper O-ring groove, but the groove geometry still needs machining.
For painting, rougher is not automatically better. Powder coating needs a profile of roughly 2–5 µm Ra to anchor, which sand blasting provides easily; a die casting at 1.6 µm Ra can be too smooth for powder adhesion and usually needs a conversion coating or light blasting first. Liquid paint hides roughness poorly: a 12.5 µm sand surface will telegraph orange-peel texture through a thin coat, so buyers who care about appearance should specify 6.3 µm Ra or a filling primer. Machining marks, not casting skin, are the usual culprit when paint looks uneven.
- Sealing faces: machine to 1.6 µm Ra max; check porosity separately with a pressure test
- Powder coat: target 2–5 µm Ra blast profile before coating
- Liquid paint, cosmetic: 6.3 µm Ra or finer, plus primer
- Gasket faces on sand castings: 3.2 µm Ra machined, flatness called out
- Any impregnation: specify leak rate and test pressure, not just Ra
Specifying Ra Without Getting Burned
Put Ra on the drawing only where it functions: sealing faces, sliding surfaces, cosmetic A-surfaces. A blanket note like "all surfaces 3.2 µm Ra" on a sand casting is a cost trap and often unachievable at the gate and riser areas. Instead, mark the specific faces, state the process (as-cast, machined, blasted), and give a maximum value, since Ra is a ceiling not a target. Add a measurement note: cutoff length 0.8 mm, measured on three readings per face, is enough to prevent arguments.
On the purchase order, pair the Ra callout with the process and the inspection method. If the foundry cannot measure Ra in-house, agree on a third-party check at first article and rely on visual comparators afterward. For high-volume die castings, note that die wear raises Ra over the tool life, so the first-article finish is the best the part will ever be. Finally, when a drawing calls for 0.8 µm Ra, confirm whether polishing or machining is expected; the price difference is significant and should be quoted explicitly.
Frequently Asked Questions
What Ra can I realistically expect on an as-cast sand part without machining?
Plan on 12.5–25 µm Ra for general green sand, and 6.3–12.5 µm with resin-bonded sand and careful facing. Anything below 6.3 µm as-cast should be quoted as a special process and verified on a first article, because gate and riser areas will be rougher than the rest of the part.
Is a smoother Ra always better for sealing?
No. Sealing depends on porosity and pit depth as much as Ra. A 3.2 µm investment casting with open surface pores can leak, while a 1.6 µm machined face with a proper O-ring groove seals reliably. Specify the sealing face, the leak rate, and the test pressure together.
How should I write Ra on a drawing so the foundry quotes it correctly?
Call out Ra only on functional faces, give a maximum value with the process (as-cast, machined, or blasted), and state the measurement method, for example 0.8 mm cutoff and three readings per face. Avoid blanket notes across the whole part, and confirm in the quote whether polishing or machining is included.
Looking for a reliable casting supplier? Request a quote from Intercontinental Casting — our engineering team replies within one business day.