Bronze Alloys for Bearings: C90700, C93200 and Friends — Load vs Embeddability Trade-offs and Substitution Traps
Publication Date : 2026-11-16 03:10:40

A practical guide for buyers specifying tin and leaded tin bronzes for bushings and bearings. Covers C90700, C93200, C93600 and C93800, the real trade-off between load capacity and embeddability, hardness and PV limits to check before you switch grades, and the substitution traps that cause field failures.
What Each Grade Actually Is
The bearing bronzes buyers ask about most are the tin bronzes (C90700, C90500) and the leaded tin bronzes (C93200, C93600, C93800). C90700 is a high-tin bronze with roughly 88-90% copper and 9-11% tin, no intentional lead, and good corrosion resistance and strength; it machines less freely than the leaded grades but holds up where lubrication is marginal and loads are steady. C93200 (SAE 660) is the workhorse: about 81-85% Cu, 6-8% Sn, 6-8% Pb, 2-4% Zn, with lead present as discrete particles that act as a dry lubricant and as the soft phase that lets grit embed. C93600 and C93800 push lead higher (around 7% and 13-16% respectively) for even better conformability and embeddability at lower strength.
Lead is the design variable, not an impurity. More lead means softer, more forgiving bearings that tolerate misalignment and dirty lubrication, but lower hardness and lower allowable bearing pressure. Less lead (or none, as in C90700) means higher strength and better fatigue resistance under rotating load, but a bearing that is far less tolerant of debris and edge loading. If your drawing says "bronze bearing" with no grade, that is the first thing to fix.
Load Capacity vs Embeddability: The Real Trade-off
Embeddability is the ability of the bearing surface to swallow hard particles so they do not score the shaft. It scales with the amount and continuity of the soft lead phase and inversely with hardness. Load capacity scales the other way: allowable bearing pressure and PV (pressure × velocity) limits rise with tin content and hardness. As a rough shop-floor guide, leaded tin bronzes like C93200 are commonly run at bearing pressures up to about 10-14 MPa (1,400-2,000 psi) with good lubrication, while a higher-strength tin bronze like C90700 can be pushed higher, roughly 17-21 MPa, provided alignment and lubrication are controlled. These are starting points for review, not universal limits — confirm against your PV, speed and lubrication method.
The practical consequence: if a customer replaces C93200 with C90700 to "get a stronger bearing," they may gain load capacity and lose the ability to tolerate contaminated grease, a slightly misaligned housing, or a shaft that deflects under load. Conversely, dropping from C90700 to C93800 to improve machinability and conformability can lead to deformation or fatigue cracking in high-load, high-cycle applications. Match the grade to the failure mode you are actually trying to prevent.
A Pre-Substitution Checklist
Before you approve any grade change on a bearing drawing, run this list. It takes an hour and prevents most of the expensive mistakes we see.
Document the original grade and its condition (as-cast, continuous cast, centrifugal cast, sintered). Confirm the application's bearing pressure, surface speed, PV, lubrication method and duty cycle. Check the mating shaft hardness and surface finish — leaded bronzes pair well with shafts around 200-300 HB and finishes of about 0.4-0.8 µm Ra. Verify the housing fit and whether the bearing is press-fit or clamped, since a softer grade deforms more during installation. Confirm operating temperature: leaded bronzes lose strength above roughly 150-175°C and should not be used near lead's melting range. Check that the substitute is available in the form and size you need — C90700 is often stocked as continuous cast bar, while high-lead grades may only come in certain cast forms. Finally, get a first-article inspection with chemistry and hardness, not just a certificate of conformance.
- Original grade, casting method and temper documented
- Bearing pressure, speed and PV calculated and compared to the new grade's limits
- Shaft hardness and Ra checked against the softer grade's requirements
- Housing fit and installation force reviewed for the softer alloy
- Operating temperature confirmed below the grade's strength-loss threshold
- Availability of the substitute in the required form and size verified
- First-article chemistry and hardness inspection required
Common Substitution Traps
Trap one: treating all "leaded bronze" as interchangeable. C93200, C93600 and C93800 differ enough in lead content that a bearing designed for C93200 may deform or crack if swapped to C93800 under the same load. Trap two: substituting C90700 for C93200 to improve strength without checking lubrication. C90700 has little free lead, so contaminated lubricant that C93200 would have embedded will instead score the shaft or seize. Trap three: ignoring the casting method. Continuous cast and centrifugal cast bar can have different porosity and lead distribution than sand castings, which changes embeddability and fatigue life even at identical chemistry.
Trap four: buying on chemistry alone. Lead segregation, porosity and hardness variation matter as much as the alloy number, so ask for a hardness map or at least hardness at several points on the first article. Trap five: overlooking regulatory and machining factors. High-lead grades machine faster but face increasing scrutiny in some markets and generate lead-bearing chips that need controlled handling. If a substitution is driven by lead restrictions, evaluate a bismuth or tin-bronze alternative with the same PV and embeddability review — do not simply drop to the nearest lower-lead grade and assume it will run.
Frequently Asked Questions
Can I replace C93200 with C90700 for a stronger bearing?
Only after checking the failure mode. C90700 offers higher strength and load capacity but much lower embeddability because it has essentially no free lead. If the original bearing was chosen to tolerate dirty lubricant, slight misalignment or shaft deflection, switching to C90700 can turn a forgiving bearing into one that scores or seizes. Recalculate PV, confirm lubrication quality and alignment, and run a first article before committing.
What is the maximum bearing pressure for C93200?
As a practical starting point with good lubrication and alignment, leaded tin bronzes like C93200 are commonly run up to roughly 10-14 MPa (1,400-2,000 psi) bearing pressure, with the exact limit depending on surface speed, PV and lubrication method. Higher-strength tin bronzes such as C90700 can go higher, but every application should be checked against its own PV and duty cycle rather than a single quoted number.
Does the casting method matter if the chemistry is the same?
Yes. Continuous cast, centrifugal cast and sand cast material can differ in porosity, lead distribution and hardness even at the same chemistry. Those differences affect embeddability and fatigue life. Ask for the casting method on the drawing and require first-article hardness checks at multiple points, not just a chemistry certificate.
Looking for a reliable casting supplier? Request a quote from Intercontinental Casting — our engineering team replies within one business day.